---
title: Soft Foot in Motors and How to Correct It
slug: soft-foot
url: /topics/guides/soft-foot/index.md
publishedAt: "2026-11-17T20:46:46"
updatedAt: "2026-11-17T20:46:46"
excerpt: "What Is Soft Foot? Soft foot is inadequate or nonuniform support at a machine&#8217;s mounting feet that lets the foot, frame, or base distort when hold-down bolts are tightened. It can exist without a visible gap. The concern is stable, suitable contact, not whether every foot carries exactly the same weight. Tightening a bolt may [&hellip;]"
authors:
  - "Ricky Smith, CMRP, CMRT"
---

# Soft Foot in Motors and How to Correct It

By [Ricky Smith, CMRP, CMRT](/authors/ricky-smith/index.md)

## What Is Soft Foot?

Soft foot is inadequate or nonuniform support at a machine's mounting feet that lets the foot, frame, or base distort when hold-down bolts are tightened. It can exist without a visible gap. The concern is stable, suitable contact, not whether every foot carries exactly the same weight.

Tightening a bolt may pull a foot into contact while bending the installation around it. The gap will be gone but the support problem is still there. That's why the investigation has to have both a check on the movement and an understanding of what's going on at the mounting surfaces.

Soft foot is a mounting condition. Shaft misalignment is the relative position of the shaft centerlines, and level is the orientation relative to gravity. They can all occur together and correcting one does not necessarily mean that the others are OK. The [common soft foot conditions](https://www.easylaser.com/en-us/knowledge-hub/the-4-different-types-of-soft-foot) are a good place to start when looking at the support.

This guide covers conventional horizontal machines with four feet and one hold-down bolt per foot. It covers how to measure their response, investigate contact, select a correction, and verify the result. Multi-bolt feet, unusual mounts, and large flexible frames require specific procedures; do not apply the four-foot sequence automatically.

## Four Common Types of Soft Foot

Parallel, angular, squishy and induced soft foot are all common teaching categories. Terminology varies, and a machine can have more than one of the conditions. Table A links each description to a physical check rather than treating a pattern of readings as a diagnosis.

**Table A Common Soft Foot Conditions**

| **Condition** | **Support problem** | **Useful confirming check** |
| --- | --- | --- |
| Parallel | Mismatched support heights | Confirm an approximately uniform gap |
| Angular | Contact surfaces meet at an angle | Map accessible gap variation |
| Squishy | Unstable or compressible interface | Inspect contamination and shim condition |
| Induced | External loading distorts the installation | Evaluate connections and supporting structure |

These categories can overlap. The table is there to guide the investigation; a single reading won't give you a diagnosis.

![Four-panel illustration of parallel, angular, squishy and induced soft foot. The induced panel shows a restrained electrical conduit connected to a motor terminal box, with an external force distorting its support. Gaps and distortion are exaggerated.](https://cms.reliamag.com/wp-content/uploads/2026/11/soft-foot-four-types-v2.png)
*Figure 1. Four common types of soft foot*

### Parallel Soft Foot

With parallel soft foot the foot and its support are approximately parallel but at mismatched heights. A motor foot may be short in relation to the others or its mounting pad may be lower. Tightening that foot will tend to put the machine into a distorted position. Short foot and rocking soft foot are related terms.

Before choosing a shim, check the gap you have with the selected foot released and the others secured. A fairly uniform gap can call for a different correction than a tapered one. Rocking or two high diagonal readings in themselves don't tell you which foot you need to add material to.

### Angular Soft Foot

Angular soft foot is where the contact surfaces meet at an angle. The foot may be bent, the mounting surface may be sloped or their relative position may create the angle. A bent foot is therefore a related term but the problem doesn't necessarily lie in the foot.

A useful clue is a gap that will vary across the accessible corners or edges under controlled bolt conditions. Note that variation and its direction. A flat shim placed across the full foot can raise it while leaving the poor contact underneath intact. The correction has to deal with the confirmed angular relationship.

### Squishy Soft Foot

Squishy soft foot (also known as spring foot) is an unstable or compressible interface. It can be caused by dirt, corrosion products, damaged shims, burrs or an inappropriate shim stack. The way the foot settles can change as the clamping is altered. An interface that may appear to be fully filled can still be unstable and not provide the required support.

Look at the pack condition and arrangement rather than just the total thickness. A bowed shim can act as a spring and contamination can prevent flat contact. Adhere to the relevant limits for the installation. There is no one maximum shim count or one fixed compression percentage that you can apply to all machines.

### Induced Soft Foot

External loading can distort an otherwise acceptable installation. Piping, conduit, bracing, coupling strain or retained jacking forces can all cause the machine to move in position or change the way its feet are sitting on their supports. If you check the installation before those loads are applied, the feet may sit differently afterward.

The question is what's changed from the acceptable state to the present state. You need to document the connection state and get the responsible people to look at the source of the strain. Adding another shim may change the reading while leaving that load in place. The corrections have to deal with the force or restraint that's distorting the installation.

## How Soft Foot Affects Alignment and Reliability

### Alignment Readings That Change When Bolts Are Tightened

An alignment move should produce a fairly predictable change. If the readings shift again when you tighten a particular bolt, the machine may have moved into a different stressed condition. Repeating the move can become very frustrating as the support condition alters the outcome of the adjustment.

Did the bolts end up in the same condition and were they tightened in the same sequence each time? Possible causes include soft foot, a measurement setup problem, looseness or movement elsewhere. A changing reading is a reason to look into it. It's not a reason to just keep adding shims until the reading on the display is what you want it to be.

### Frame Distortion and Component Loading

Mounting distortion can have an effect on the relationship between the bearing housings and other internal components. Depending on the machine construction and the amount of distortion present, that can lead to a change in internal alignment, clearances or component loading. The issue is not confined to the shaft-to-shaft alignment that you can see at the coupling.

Those changes can lead to wear and reliability issues, but the outcome is highly dependent on the installation. A small mounting error doesn't necessarily equate to a bent shaft or a failed seal. If a machine has a history of recurring component failure, you need to look at the support condition as part of your investigation rather than simply assigning a failure mechanism from the soft foot reading.

### Why Vibration Alone Does Not Confirm Soft Foot

A change detected through [vibration analysis](https://reliamag.com/topics/articles/vibration-analysis) can prompt a mounting investigation. The overall value or spectrum will not tell you how each foot contacts the base or what correction it needs. The same symptoms can be caused by a number of different things and the mounting will still need to be checked physically.

Stop and isolate the machine before you perform the controlled bolt-release and contact checks described here. Don't loosen the mounting bolts on a running machine just to see if the vibration changes. Use the vibration as supporting operating evidence and then use a repeatable stopped-machine assessment to determine whether you need to correct the support.

## How to Check for Soft Foot

### Prepare the Machine and Record the Starting Condition

Stop and isolate the equipment under its applicable energy-control procedure. OSHA's requirements for the [control of hazardous energy](https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.147) include isolation and verification before servicing where the standard applies. A simple stop button does not constitute isolation. You must also address any stored energy and the potential for it to return as part of the procedure.

Check the accessible feet, the mounting pads, the hardware and the shims. Deal with any obvious defects and do the required rough alignment before the controlled check. Releasing one bolt for the purpose of taking a measurement is a completely different thing from lifting, moving or reshimming the machine. Access underneath it requires approved lifting and support.

Label the feet and record the viewing direction, coupling condition, external connections and instrument setup. Get the required bolt torque and tightening sequence. Record any initial deviations from those conditions so that the final comparison is valid. Follow the equipment and instrument instructions for this procedure.

### Choose the Measurement Method

The difference between [shaft response and local foot movement](https://acoem.us/blog/other-topics/soft-foot-primer-part-1-measuring-soft-foot-just-effect/) is important when selecting a tool. An indicator, a laser and feeler gauges all provide useful information. You need to know what is being displayed and in what units before you can interpret the result.

**Table B What Each Measurement Method Shows**

| **Method** | **What it shows** | **Important limitation** |
| --- | --- | --- |
| Dial indicator | Movement at its contact point relative to its reference | Reference stability and placement affect the reading |
| Laser soft foot function | Response at the shaft or coupling, with a derived result | Displayed value is not automatically shim thickness |
| Feeler gauges | Accessible physical gaps under defined bolt conditions | One gap does not establish the entire contact pattern |

Record the method, units, location, bolt condition and the connection condition. Compare like measurements before and after the correction has been made. The derived result from a shaft-mounted system is not automatically going to be the air gap or the shim thickness required.

![Dial indicator on a stable reference with its probe contacting the motor foot; inset shows one foot released and the other three secured.](https://cms.reliamag.com/wp-content/uploads/2026/11/soft-foot-dial-indicator-setup.png)
*Figure 2. Dial indicator setup for a controlled soft foot check*

### Measure One Foot at a Time

Establish the required starting bolt condition (normally with all four feet secured for this controlled check). Ensure you have a stable indicator reference and a good contact point, or the correct laser mount, dimensions and geometry. A reference that moves with the part can hide the movement you're trying to measure.

Use [an instrument-specific soft foot procedure](https://easylaser.com/files/files/manuals/XT%20Manual/en/Content/E_Horizontal/Softfoot.htm) to establish precisely when to zero, when to observe and when to save the values. Some systems will record the result after the bolt has been retightened and the reading has settled. Don't assume that all instruments will work in the same way.

* Select one foot and release its clamping load as directed by the procedure, leaving the other three feet clamped. Let the response settle and watch the movement that is indicated.
* Record the response and the required test conditions at the prescribed point in the instrument's sequence. Note the instability rather than picking the most convenient value from a drifting display.
* Retighten the selected foot to the required condition and allow the reading to stabilize again. Record the reading as required before moving on to the next foot.
* Repeat for the remaining feet and record all four results. Don't assume a universal number of bolt turns. Keep the other three feet secured during this check; use any alternative diagnostic method only under its specific procedure.

### Map the Contact Pattern With Feeler Gauges

With the selected foot released and the other three secured, check the accessible gap locations as the approved procedure permits. Keep the bolt state defined during the check. Note where each measurement was taken rather than just recording a single, unlabeled gap value.

Compare the accessible corners or edges to see whether the gap is fairly consistent or varies across the foot. A simple sketch will show you the outer edge, inner edge and the direction of any taper. Don't describe an inaccessible point as measured and don't assume it will be the same as the nearest accessible point.

Don't force the gauge into the interface. Forcing the blade under the foot can change the gap you're trying to measure. Check for debris and unstable shims as access permits and use the appropriate support if further access is required.

These observations will help in selecting the correction. A movement value shows the response to a change in clamp load. It does not give you the full support profile underneath the foot.

![Feeler gauge checking accessible gaps beneath an integral cast motor foot with its hold-down nut released. A location map and small profiles compare uniform and tapered gaps.](https://cms.reliamag.com/wp-content/uploads/2026/11/soft-foot-feeler-gauge-measurement-v2.png)
*Figure 3. Checking accessible foot gaps with feeler gauges*

### Check Repeatability and External Strain

Repeat the questionable readings with the same bolt sequence, same instrument setup and same connection conditions. If the result changes significantly, then establish why before you make a correction. Acoem's discussion of [soft foot measurement and repeatability](https://acoem.us/blog/shaft-alignment/soft-foot-what-it-is-and-how-to-minimize-it/) points to both the tightening sequence and the potential for movement in the supporting base.

Check the mounting geometry, instrument reference stability, base flexibility and external loads. A quiet indicator or laser reading in no way rules out all support defects if the base is moving with the foot. Document any visible movement and any contact evidence even if this is at odds with the displayed value.

Assess the driver and the driven equipment as appropriate. A problem with the support arrangement of either machine can complicate the job. Keep the comparison tied to the stated coupling and connection condition.

Before disconnecting piping or another loaded connection, follow the procedures for isolation, support, and disconnection. Treat that as planned work with the responsible people, not a quick check to see if the reading improves.

## What Is an Acceptable Soft Foot Tolerance?

A frequently used criterion in alignment guidance is 0.002 inch (2 mils). A mil is 1/1000 of an inch. The exact conversion is 0.002 inch = 0.0508 mm, which is generally rounded to 0.05 mm. LUDECA's [soft foot measurement and correction guidance](https://ludeca.com/wp-content/uploads/2016/12/Ludeca_SoftFoot-Causes-Characteristics-and-Solutions.pdf) uses the 0.002-inch criterion in its stated checking procedure.

Easy-Laser flags readings above 0.05 mm in its parallel soft foot example, while Acoem uses a 0.002-inch feeler blade for its final check. These are similar numerical benchmarks applied to different measurements and procedures.

That number gives useful context, but acceptance depends on the relevant equipment specification and measurement method. A feeler gauge gap, a direct foot displacement and a laser-derived value are all different quantities. Don't apply a limit from one method to another without confirming that the requirement actually applies to the quantity you're measuring.

Before you accept a result you must know what the requirement actually is, which instrument and setup it applies to and what bolt and connection conditions are specified. A software default doesn't establish the machine specification. If the equipment instructions and instrument guidance appear to be in conflict, resolve the requirement rather than picking the limit that's easiest to meet.

Soft foot acceptance is also entirely separate from shaft alignment acceptance. A value within the applicable limit doesn't establish correct shaft alignment, a sound foundation or good contact at all locations. You have to consider the reading in light of the physical findings and the final installation requirements.

Record the acceptance criterion with the results. That way the next person can tell the difference between a requirement that's been properly verified and one that's just a rule of thumb they've remembered or a display setting that's been carried over from some other job.

## How to Correct Soft Foot

### Restore Clean and Stable Support

Fix the confirmed condition rather than just going ahead and doing every repair described below. Start by restoring clean, stable contact where you have contamination, burrs, damaged shims or another obvious defect that interferes with the support. Adding material over a defect can mask it while leaving the installation unstable.

Inspect the foot and its support using the appropriate access and lifting arrangements. Replace any unsuitable shims and refer any damaged mounting surfaces for the correct repair. Don't grind a foot or base without an approved repair decision, pry the machine into position, or use your hand to support it while changing the interface.

### Correct Parallel Gaps With Suitable Shims

For a confirmed parallel gap, choose the shim change from the contact measurements, the verified shim thickness and the alignment requirements. The object is to have suitable support at the required machine position. Don't simply add the displayed amount beneath every high-reading foot.

Use clean, flat shims with sufficient support area and clearance around the hold-down bolt. The manufacturer's [shimming practices](https://www.easylaser.com/en-us/knowledge-hub/the-dos-and-donts-of-shimming) explain why shim condition, size and measured thickness are all important. Keep the stack as simple as possible within the limits of the actual installation. Don't assume nominal markings tell you the actual thickness of an existing shim pack.

Record the material added or removed at the specified foot. Keep the machine's required elevation and available alignment adjustment in mind. A support correction can alter the shaft position so you still need the subsequent measurement and alignment checks.

![Clean, flat motor shims compared with a bowed shim, a raised burr and contamination, plus a view of adequate support beneath a foot.](https://cms.reliamag.com/wp-content/uploads/2026/11/motor-soft-foot-shim-pack-inspection.png)
*Figure 4. Inspecting shims for flatness, cleanliness, and adequate support*

### Correct Angular Contact at Its Source

If the gap is tapering then adding an equal thickness across the whole foot will leave the same angular mismatch. You need to establish whether it's the foot, the mounting pad or the relationship between the two that is the problem. A cracked foot or a damaged support will obviously require a repair decision before it even becomes a shimming issue.

Depending on the equipment, the appropriate correction could be repair or machining of the affected surfaces, or the use of an approved engineered chock or other engineered support. Chocks provide fitted support between the machine and the mounting surface. The approach selected must be appropriate for the load and the installation.

Partial or stepped shims require a justified application in accordance with the applicable procedure. They must not be used as a general-purpose homemade wedge or a folded shim. The contact problem and the approved correction must be recorded so that subsequent alignment work doesn't inadvertently remove or reposition a necessary support feature.

### Address External Loads and Base Movement

Where external loading is the cause, identify the source and get the people who can fix it. Piping support and fit, conduit restraint, coupling condition, bracing or retained jacking forces may all be the issue. Another shim is not going to fix a load that's distorting the installation.

Don't pull the piping into position with the flange bolts or overtighten the hold-downs to force the machine flat. If the base itself is moving, then look at the support, the attachment and the foundation condition. Fixing the motor feet alone may leave that base movement unresolved.

Document the conditions before the work and then again after the required connections have been restored. A check with that load removed can't tell you whether the finished installation meets requirements. Recheck with the required connections restored and compare the response under the same defined conditions.

### Tighten Consistently and Repeat Every Foot Check

Restore the specified torque and tightening sequence following correction. Repeat the measurement procedure at each foot, using the original labeling, geometry and relevant connection conditions. Compare each result with the appropriate acceptance criterion. If the values are still unstable or inconsistent, then investigate rather than accept a favorable pass through the sequence.

An improvement at one foot doesn't necessarily mean the other three are still acceptable. Changing the support at one location can have an effect on how the frame behaves at other locations. Record the new shim arrangement and all the final readings (including the feet that didn't receive a shim change). The useful record will tell you both what was changed physically and how the installation responded in the end.

### Complete Shaft Alignment and Verify the Installation

Complete precision shaft alignment and check the result after final tightening. If the alignment requires further shim or position changes, recheck for soft foot because the support conditions may have changed. Keep the required support corrections in place through the alignment work rather than treating them as just temporary setup adjustments.

Restore the guards and go through the site's return-to-service procedure. Appropriate operating observations can help assess the completed work, but reduced vibration alone is not sufficient to prove that all the support and alignment requirements have been met. Close the job with the final bolt condition, soft-foot results and alignment record rather than just a satisfactory startup observation.

## Soft Foot Measurement and Correction Example

This example is hypothetical. A horizontal motor has four feet and one hold-down bolt per foot. The machine is isolated, the laser setup is documented and the specified torque, the tightening sequence and the coupling and connection conditions are all held constant. The example is based on a local limit of 0.002 inch or less for that particular laser-derived result.

### Compare the Readings With the Contact Evidence

Looking from the coupling end toward the motor, left front (LF) and right front (RF) are the near feet; left rear (LR) and right rear (RR) are the far feet. Each of the initial results in Table C is from a separate one-foot release with the other three feet secured. RF and LR have the high diagonal readings.

**Table C Hypothetical Motor Results in Inches**

| **Foot** | **Initial laser result** | **Shim added** | **Final laser result** |
| --- | --- | --- | --- |
| LF | 0.001 | 0.000 | 0.001 |
| RF | 0.006 | 0.004 | 0.001 |
| LR | 0.005 | 0.000 | 0.001 |
| RR | 0.001 | 0.000 | 0.001 |

The RF shim addition comes after a separate, essentially uniform 0.004-inch gap check (not the initial laser value). The final values are just illustrative remeasurements. The example uses a method-specific criterion of no more than 0.002 inch.

With RF released and the other three feet secured, the technician checks the gap with a feeler gauge at several points. It measures about 0.004 inch at each accessible spot. The technician then retightens RF before releasing LR and checking it the same way. At LR, the gap is widest at the outside corner and narrows toward the inside corner.

The 0.006-inch laser reading at RF comes from movement sensed at the coupling. A measurement at the foot helps determine the correction. In this example, the uniform gap at RF calls for a 0.004-inch shim there. With that shim in place and the original pack still under LR, the LR reading drops from 0.005 to 0.001 inch on the recheck.

![Hypothetical RF example showing a 0.006-inch laser-derived result, a separate uniform 0.004-inch gap and a selected 0.004-inch shim. The released nut is clearly separated from the washer; all four feet must be remeasured after correction.](https://cms.reliamag.com/wp-content/uploads/2026/11/soft-foot-gap-and-shim-v2.png)
*Figure 5. Displayed response, accessible gap and selected correction in the hypothetical example*

### Remeasure and Confirm the Result

After the RF correction, all four feet are remeasured under the same defined conditions. The final values of 0.001 inch are illustrative observations, not numbers derived by subtracting shim thickness from the original readings. Each of them now satisfies the specific laser-result criterion of the example. There is no claim that another motor would give these results.

Recheck the same accessible spots at RF and LR with a feeler gauge. Release one foot at a time, keep the other three secured, and retighten each foot after checking it. At LR, compare the outside and inside corners to see whether the gap still tapers. If contact at either foot falls outside the equipment's requirements, find and correct the cause before accepting the installation, even if all four laser readings are within tolerance.

Finish the shaft alignment and recheck for soft foot after any further adjustment. Document the final bolt torque and sequence, the connection conditions, the readings and the RF shim addition. Keep the individual gap measurements so that a later reader can see why that shim addition was chosen.

Passing the example's soft foot check doesn't complete the installation by itself. That just establishes one result under the stated conditions. Alignment and the other return-to-service criteria still need to be checked.

## How to Prevent Soft Foot

Preventing recurrence depends on retaining good support through installation and later work. Five practices make that easier:

* Keep clean, sound mounting surfaces. Check them when you have access and follow the approved repair procedure for any damage. Tightening up to hide a gap won't help because it doesn't restore the missing support or make a bad surface good.
* Inspect and record the shim packs. Note their location and configuration and replace any that are damaged or contaminated. It's not acceptable to keep a pack in place simply because you're used to it, if the material in question no longer provides a stable contact.
* Control bolt torque and tightening sequence. Use the specified conditions consistently so that the checks can be compared. If a result changes with the tightening sequence, then that behavior must be resolved before signing off on the alignment.
* Verify support following any disturbance to the installation or any change to the connected load. Alignment moves, piping work and other changes can all have an effect on the condition you previously accepted. A machine being level doesn't guarantee that its feet have adequate support.
* Keep the method of measurement, all the foot readings and the final alignment record. That helps keep you from treating every high reading as a shim instruction or just accepting the foot that's improved. You need to record the connection conditions so that the next check has a sensible baseline to work from.

Use these practices when installing or servicing the machine; they don't define a universal calendar interval. Perform and document a soft foot check on the next applicable installation or alignment job.

## Frequently Asked Questions About Soft Foot

### Is Soft Foot the Same as Shaft Misalignment?

No. Soft foot is a mounting and support condition; shaft misalignment is a condition relating to the position of the shaft centerlines relative to each other. Mounting distortion can have an effect on alignment so the two problems can occur in conjunction. Correcting soft foot will not necessarily give you acceptable shaft alignment and an acceptable alignment reading in no way proves that you have suitable support at every foot.

### Can a Motor Have Soft Foot With All Four Feet Touching?

Yes. A foot may touch along only part of its surface, rest on unstable contamination or be pulled into contact by external loading. Visible contact does not necessarily equate to stable support. Check movement under controlled bolt conditions and inspect the contact surfaces to see how each foot sits on its support.

### Should Soft Foot Be Checked With the Coupling Connected?

Follow the equipment and instrument procedure and record the coupling condition used. Coupling strain can have an effect on the results so neither connected nor disconnected is a universal rule. The required installed condition must be checked before acceptance and the relevant checks repeated if the coupling condition changes during the work.

### Can a Laser Alignment Tool Replace Feeler Gauges?

They answer different questions. A laser system measures the response at the shafts or coupling and may derive foot values from it. Feeler gauges investigate accessible physical gaps under defined bolt conditions. That contact investigation may still be necessary to select a correction, even when the laser identifies a high reading.

### Why Do Diagonally Opposite Feet Show High Readings?

The supports interact through the machine frame. A condition at one location can produce movement when another foot is released, including a diagonally opposite foot. The pattern calls for a controlled contact investigation. It does not prove that both feet require shims or that either displayed value equals the needed thickness.

### Why Does Soft Foot Return After Shimming?

The cause may remain unresolved, or the installation may have changed. Damaged contact surfaces, unstable packs, different torque or sequence, alignment adjustments, and external strain can affect the result. Repeat the measurement under documented conditions and investigate the cause rather than adding shims each time the reading returns.

## Related Articles

[Mechanical Maintenance 101: A Guide to Belt, Chain, and Coupling Care](https://reliamag.com/topics/articles/mechanical-maintenance-belt-chain-coupling)

[How Precision Alignment Can Transform Motor Reliability and Efficiency](https://reliamag.com/topics/articles/precision-alignment-motor-reliability)

[Why Shaft Alignment Tolerance Standards Matter for Bearing Life](https://reliamag.com/topics/cartoons/shaft-alignment-tolerance-standards)

[What Causes Bearing Fatigue Failure, and How to Catch It Before the Breakdown](https://reliamag.com/topics/cartoons/bearing-fatigue-failure)

[Vibration Analysis: Techniques, Tools, and Benefits](https://reliamag.com/topics/articles/vibration-analysis)

## Sources

Easy-Laser. [The 4 Different Types of Soft Foot](https://www.easylaser.com/en-us/knowledge-hub/the-4-different-types-of-soft-foot). September 21, 2021.

Acoem USA. [Soft Foot, What It Is and How to Minimize It](https://acoem.us/blog/shaft-alignment/soft-foot-what-it-is-and-how-to-minimize-it/). Brad Case. June 4, 2010.

Acoem USA. [The Soft Foot Primer Part 1, Are You Measuring Soft Foot or Just Its Effect](https://acoem.us/blog/other-topics/soft-foot-primer-part-1-measuring-soft-foot-just-effect/). Stan Riddle. February 19, 2018.

Easy-Laser XT Manual. [Softfoot](https://easylaser.com/files/files/manuals/XT%20Manual/en/Content/E_Horizontal/Softfoot.htm). Undated online manual; accessed November 17, 2026.

Easy-Laser. [The Dos and Don'ts of Shimming](https://www.easylaser.com/en-us/knowledge-hub/the-dos-and-donts-of-shimming). December 3, 2019.

LUDECA. [Soft Foot, Causes, Characteristics and Solutions](https://ludeca.com/wp-content/uploads/2016/12/Ludeca_SoftFoot-Causes-Characteristics-and-Solutions.pdf). Alan Luedeking. 2014.

